Shields

Are you developing a complex IoT device with your MKR board and running out of memory? Add Flash memory and microSD storage to your MKR board, and allow over-the-air updates, with the Arduino MKR MEM Shield. The Arduino MKR MEM shield will allow you...

Simply mount your MKR1000 to this new adapter and plug in any of your UNO shields! The MKR2UNO Adapter allows you to turn your Arduino UNO form factor based project into a MKR based one without too much effort! You can so upgrade your project with a...

The MKR Relay Proto Shield allows you to easily command relays with your MKR board. The shield provides two on board relays and a small prototyping area if you need to add some other component to your project. The MKR Relay Protoshield allows you to...

CAN-BUS is a common industrial bus because of its long travel distance, medium communication speed and high reliability. It is commonly found on modern machine tools and as an automotive diagnostic bus. Thanks for CAN-BUS, makers are able to hack...

The 1Sheeld+ is an easily configured shield for Arduino. It has a built-in bluetooth low energy module that gives to your Arduino the capability to connect itself to your iOS and Android phones. Thanks to the 1Sheeld app available on the App...

This Starter Shield is a perfect choice for the beginners of Maker World. By playing with it, you can literally learn some basic skills that are required to be a maker, like soldering techniques, basic electronic circuit principles and programming...

    This Phoenard board extension can be docked using the bottom 30-pin connector, exposing most (not all!) Arduino pins. You can then connect Arduino board extensions to the device easily. If you want one Phoenard, please...

SIM808 Shield is an Arduino compatible shield that based on SIM808 module, it offers 2G GSM and GPRS data along with GPS technology for satellite navigation.   What’s it for: Receive GPS data and A-GPS data Send and receive SMS...

  The Audio Hacker shield for Arduino allows you to perform realtime digital signal processing. Record audio samples into memory and play them back. Mix samples, manipulate audio, build audio effects, or synthesize entirely new sounds. All...

BLE-Shield v3.0.0 based on Bluegiga’s BLE113 Module   The Bluetooth Low Energy (BLE) Shield v3.0.0 for Arduino is a Shield that enabled Arduino Projects to communicate with Bluetooth 4.0 enabled smartphones and tablets. Version 3.0.0...

The BTstack LE Arduino Shield provides a complete Bluetooth Low Energy solution for the Arduino platform. With it and the provided BTstack Bluetooth Stack library, the Arduino can act as LE Peripheral or LE Central devices...

E-paper might be the most lightweight and comfortable material to read. It reflects light instead of emits light to mimic the experience of conventional paper reading. And in this way much less power is consumed.    Small e-paper shield...

The EasyVR Shield 3 is an adapter board for the EasyVR 3 module, designed to simplify its use among the Arduino community.   The Shield is compatible with any Arduino board using UNO-R3 Shield headers, running at either 3.3V or 5V levels, by...

The Relay Shield provides four high-quality relays that can control high current loads to Arduino / Seeeduino boards. It also provides NO (Normally Open) / NC (Normally Closed) interface. It could be a nice solution for controlling devices that could...

The solar charger is a stackable shield to Arduino compatible platforms, enables adaptive battery power and act as energy harvester for in-field charging. You may use various batteries that has the voltage of 3.0V-4.2V to shift up for 5V output, or...

  Introduction: Make your own touchless control interface providing 3D coordinates and gestures in the form of an Arduino shield 3Dpad is an innovative and experimental system that you can use for creativity, experiments and education...

Introduction:   The LogicStart Shield provides everything needed to get started with VHDL and FPGA development on the Papilio with one convenient and easy to connect circuit board.   Learn VHDL with Mike Field's free...

Camera Shield is the first shield board that support photograph, it is based on the solution of VC0706 + OV7725, the former is a high performance camera processor with enhanced image processing functions and it embedded the hard-wired JPEG codec, and...

emperature and Humidity (T&H) remain top on the list for DIY Maker projects' sensing needs, many T&H sensorsare constructed from thermistor / low priced capacitive humidity sensor are not accurate for serious projects. This Temperature...

NOTE: It is recommended to use the upgraded version, 1Sheeld+ as your alternative choice. Imagine an Arduino Shield that can be configred to be an LCD, GPS, Wuifi, or any shield you may think of!     1Sheeld is a new easily...